A gas boiler, fuelled with natural gas, oil, LPG or propane (etc), is the most common kind of appliance used for central heating in Myddlewood Shropshire SY4 and throughout the United Kingdom. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual boiler inspection and maintenance check by a registered “Gas Safe” gas boiler service heating engineer is essential for safety and comply with UK Law.
The Engineer will make sure that the heating system is installed according to regulations during the annual central heating and boiler inspection, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler breakdowns and the resulting emergency repair work can often be avoided.
Myddlewood Shropshire SY4 Super Low Energy Combi Boiler Inspection – Several Things You Should to Consider
By opting for a condensing boiler to convert energy of natural gas to heat your home or apartment you are not only helping yourself by saving on heating bills but also make possible environmental well being while helping the whole world.
Wasted energy = wasted money
Whatever the fuel type may be, is said to be efficient about 90% at the lower end and – 98% at the upper. Your 15 year or so old traditional oil fired boiler is at least 12% less efficient than this. Whether it is gas or oil, you can imagine how much fossil fuel the high efficiency boiler would conserve, how much CO2 emission it would curtail and the pile of moolah you would save during the next 30 or 40 year plus life span.
What makes a condensing boiler more efficient?
A traditional gas burning boiler or a condensing boiler of recent vintage technology is not different to any oil burning boiler in basic working mechanism. The extra bit of efficiency in boiler is due to the condensation of water of combustion from steam state to liquid, releasing the latent heat of vaporisation. (Sadly if not for the condensing boiler, this huge percentage of heat energy will be sent up through the chimney as flue gases, without the home owner having a clue to what’s happening). Inherently any boiler can achieve fuel efficiencies of 90% upwards easily.
A centralized heating system, incorporating a condenser boiler depends on several other system components. These would include the control system, DHW cylinders, Terminal units such as radiators etc. Unless there is a collectively efficient system in operation the ultimate overall efficiency will not be as desired.
Proprietary Brands and advanced designs
Proprietary brands such as Viessmann, a world leader in this field have developed technologies such as their stainless steel Inox-radial heat exchangers for natural gas combustion, capable of extracting almost to the end of last wave of thermal energy otherwise just wasted. Vitotronic controls (microprocessor based control system), Vitocell domestic hot water cylinder, lambda pro control combustion controls (a metering system that adjust the combustion process to the properties of any gaseous fuel) are other advanced features developed by them. The ultimate result is a very welcome consistent fuel efficiency of about 98%.
Why the Condensing Combi Boiler is a Very Popular Unit
There comes a time in every homeowner’s life when they must wrestle with the decision of whether or not they should repair their existing heating system, or bite the bullet and purchase a new one. Boilers and furnaces are one of the most expensive pieces of equipment in your home, so naturally you want to get as many years of service out of them as possible. Yet some times, it just doesn’t make sense to make small repairs on a unit well past its prime.
The best way to prolong your system’s lifespan is to ensure you have your system professionally serviced annually. This will help ensure the unit is running at maximum efficiency. It will also ensure that small problems are brought to light before they become larger expenses. However, when problems do come up, consider the following:
Is the problem easily fixable?There are many components of a HVAC unit that can easily be replaced; yet when some parts go it is much more difficult to fix. For example, ignition modules, thermocouples, or zone controls are all components that are easily replaced on heating systems. Yet, when a section of your boiler cracks, there is not much you can do except purchase a new unit.
Likewise, on air conditioners and heat pumps – many things can go wrong which are fixable. But when the evaporator coil or the condenser fails they are not easily repaired. And one of these parts needs to be replaced, it is best to replace the other with a compatible unit. Coils and condensers which are not matched can function together, but will not run optimally. Mismatched units will show decreases in performance, increased energy use, and premature system failure. So despite the higher initial cost, it is a smarter move to replace both components at the same time for maximum efficiency and prolonged equipment life.
Is the equipment inefficient?Another point of consideration is whether or not it pays to keep an outdated piece of equipment running in your home. If your boiler or furnace is over 15 years old, the efficiency is probably somewhere between 50-75%. Newer high efficiency models are between 85-95% efficient. Replacing an outdated unit with a new high efficiency model will save you money on your fuel bill.
What can go wrong next? If you have an older piece of equipment, you also must consider what may go wrong next. Making multiple small repairs can add up fast. If your unit is fixable, but the cost of repair is high, you may want to consider replacement. While it will be more expensive up front, you will save money in small repairs down the road, as well as save yourself a few headaches.
For Myddlewood Shropshire SY4 Systems We Often Suggest Purchasing From The Top Combi Boiler Range
A gas boiler, fuelled with natural gas or propane, is one kind of appliance used for central heating. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual maintenance check by a registered gas boiler service heating engineer is very important for safety and efficiency. They will make sure that the heating system is installed according to regulations, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler repair work can be avoided.
In order for the boiler to be serviced properly it needs to be working.
Gas boiler service varies according to the type of boiler, but there are some things that should be checked on in any boiler. This will be done by the engineer according to the instructions in the manual which came with the boiler when it was installed. The main things that should be checked are:
1. check for leaks
2. check the gas pressure
3. check if it is producing carbon monoxide
4. check if it is functioning properly
5. check the overall condition
6. check the pump and valves
7. check for enough ventilation
8. check the safety and cleanliness of the flue
Old cast iron boilers that have an open flue will need to be dismantled and cleaned which is not needed for modern boilers. They have a systems performance test. Depending on the condition and type of boiler it can take anywhere from a half an hour to an hour and a half for a complete gas boiler service. Contractors are often willing to do servicing, especially during the summer, for greatly reduced prices, hoping that you will call them later if you need any gas boiler repair work.
If there is concern that a boiler is not working properly, and gas service is required, there are some things that can be checked:
1. Make sure there is enough water pressure by looking on the pressure gauge. It should show 1.0-1.5 bar.
2. Make sure the pilot light is lit.
3. If the pilot light is lit but there is no hot water, or it is unusually noisy, it may be a gas valve or pump failure in which case an engineer needs to be called.
4. If there is hot water but no central heating, the diverter valve may not be functioning.
5. If the top of the radiator is cold it may need to be “bled”. There is a bleed valve near the top that will release air. If it is cold on the bottom there is most likely sludge or rust blocking the radiator.
If there is no heat at all check the gas and make sure it is turned on as well as the thermostats and control switches. Make sure the pump is running and make sure the pilot light is lit. Many of these minor gas boiler repairs can be done at home with the use of the manufacturers’ manual. If you can identify a problem, but are not sure how to fix it even with a manual, call a heating engineer for routine gas boiler service.