A gas boiler, fuelled with natural gas, oil, LPG or propane (etc), is the most common kind of appliance used for central heating in Edgebolton Shropshire SY4 and throughout the United Kingdom. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual boiler inspection and maintenance check by a registered “Gas Safe” gas boiler service heating engineer is essential for safety and comply with UK Law.
The Engineer will make sure that the heating system is installed according to regulations during the annual central heating and boiler inspection, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler breakdowns and the resulting emergency repair work can often be avoided.
Edgebolton Shropshire SY4 High Energy Efficiency Combi Boiler Inspection – 5 Things You Will Want to Take Note Of
It is important to maintain boiler systems properly. The best way to do this is to get your boiler serviced frequently. Experts and manufacturers themselves recommend getting your boilers serviced at least once a year, to be on the safe side. Servicing a boiler can make it more efficient and increase its performance. This keeps it in a good and functional condition, making it last longer. Although the sound of servicing your boiler might seem expensive, especially on a yearly basis, the cost will only go up the longer you put it off. In addition to this, it can become harmful and dangerous to all those living in the same house.
A yearly servicing is the recommended frequency; however, there are a few exceptions to this rule that must be taken into account for. Moving into a new house with a boiler already installed needs to be serviced too before it is used. You cannot be sure how old the boiler is, or how long it has been since it was last used or serviced, so it is always best to be safe than sorry. Also, it is recommended to get your boiler serviced if you have been on an extended holiday where no-one has been at home to use the said boiler. A dormant boiler can be filled with anti-freeze that must be drained before use once again. Also, once again, after not being in use for a long time, you cannot be sure the condition of the boiler. There may be clogged or broken parts which to someone who isn't trained in the profession of servicing boilers would be unaware of.
The best time for getting a boiler service done is in between August and October, the last few months of summer. Not only is this after the holiday period, where you might have left the boiler unused for some amount of time, but these months are the in the off-peak season so many service providers would be both available and able to offer you a discount. This means that you can save on money and get a good, professional service from a trained and licensed expert without any hassle. Leaving the service for even a few weeks after this time period will see a rise in the price and the busyness of the workmen as winter comes around and boilers start to break and need fixing.
A good boiler service provider is someone who has a good reputation and is qualified. Finding someone like this isn't hard, as there are many professionals out there, however, it is essential that you make sure that the person you choose to hire is an expert in the boiler servicing field. Checking a person's or a company's licenses can be easily done by logging onto the Gas Safe Register in the United Kingdom and looking up their names. The industry of boiler servicing is very lucrative, with many of your local company's and independent workers offering competitive prices for a variety of different services including boiler servicing. It is important not to get too distracted by the pricing when hiring someone to do the job.
Your boiler system manual is the best place to start when looking for information about its servicing. The manufacturer can also help you by answering any questions you might have that are not mentioned in the manual. Phone numbers and email addresses are usually provided with the manual, but if not, it can be easily found on the internet.
Dependable Gas Boiler Brands For Your Home
There comes a time in every homeowner's life when they must wrestle with the decision of whether or not they should repair their existing heating system, or bite the bullet and purchase a new one. Boilers and furnaces are one of the most expensive pieces of equipment in your home, so naturally you want to get as many years of service out of them as possible. Yet some times, it just doesn't make sense to make small repairs on a unit well past its prime.
The best way to prolong your system's lifespan is to ensure you have your system professionally serviced annually. This will help ensure the unit is running at maximum efficiency. It will also ensure that small problems are brought to light before they become larger expenses. However, when problems do come up, consider the following:
Is the problem easily fixable?There are many components of a HVAC unit that can easily be replaced; yet when some parts go it is much more difficult to fix. For example, ignition modules, thermocouples, or zone controls are all components that are easily replaced on heating systems. Yet, when a section of your boiler cracks, there is not much you can do except purchase a new unit.
Likewise, on air conditioners and heat pumps - many things can go wrong which are fixable. But when the evaporator coil or the condenser fails they are not easily repaired. And one of these parts needs to be replaced, it is best to replace the other with a compatible unit. Coils and condensers which are not matched can function together, but will not run optimally. Mismatched units will show decreases in performance, increased energy use, and premature system failure. So despite the higher initial cost, it is a smarter move to replace both components at the same time for maximum efficiency and prolonged equipment life.
Is the equipment inefficient?Another point of consideration is whether or not it pays to keep an outdated piece of equipment running in your home. If your boiler or furnace is over 15 years old, the efficiency is probably somewhere between 50-75%. Newer high efficiency models are between 85-95% efficient. Replacing an outdated unit with a new high efficiency model will save you money on your fuel bill.
What can go wrong next? If you have an older piece of equipment, you also must consider what may go wrong next. Making multiple small repairs can add up fast. If your unit is fixable, but the cost of repair is high, you may want to consider replacement. While it will be more expensive up front, you will save money in small repairs down the road, as well as save yourself a few headaches.
For Edgebolton Shropshire SY4 Systems We Usually Suggest Buying From The Vaillant Combi Boiler Range
Oil fired condensing boilers are just starting to be used in the United States. There are some obstacles to overcome and some great advantages to condensing oil technology.
One of the main reasons that they have not been used more is because of the lack of low-sulphur heating oil being readily available. A condensing oil boiler must burn the low-sulphur heating oil for it to work properly. As more and more of these units are sold in different areas of the US the right fuels will become more readily available.
Modern oil condensing boilers can save you as much as 30% more energy than many conventional boilers. A modern oil condensing boiler will not only heat more efficiently, but because of this it will reduce your heating oil consumption. When low-sulphur heating oil or heating oil with biogenic additives are used in an oil condensing boiler, it then becomes almost as environmentally friendly as using natural gas.
If your boiler is more than 15 years old, replacing it with a new condensing boiler, of the right heat output for your property size, should save you around a third on your heating oil bills. If you plan to install a new boiler or to replace an existing one, in some cases you will need to install a condensing boiler to meet today's higher standards for energy efficiency required under many building codes. Today's new boilers are not only smaller, neater, they also take up less space, Therefore they are much more energy efficient and therefore use less fuel to produce the same amount of BTU's. A typical conventional boiler burns fuel in a combustion chamber that is surrounded by a water jacket. Condensing boilers also extract the heat from the products of combustion using a secondary heat exchanger.
A condensing combi boiler is a boiler that will heat your home and provide you with instantaneous hot water, without adding a hot water tank. Most of these boilers use a coil that is immersed in the hot water inside the boiler. The cold water is run through the coil and the heat is transferred from the boiler water to the domestic water. These boilers make the production of your hot water very efficient also.
Condensing oil boilers basically are not that much different than conventional boilers. They just are designed so that they reduce the flue gases temperature to the point where the water vapor in the exhaust is cooled to the point where it condenses. This condensing feature also releases the latent heat in the flue gases. This heat is also collected and used to heat you home.
Condensing boilers are not only a great deal for new construction, but they can also be used to upgrade many old heating systems. They are nearly the same size as older boilers and in some cases they are smaller. The piping may have to be reconfigured a bit, but a good contractor can fit an oil fired condensing boiler easily into any system. You gain will be a highly efficient and comfortable heating system.