A gas boiler, fuelled with natural gas, oil, LPG or propane (etc), is the most common kind of appliance used for central heating in Condover Shropshire SY5 and throughout the United Kingdom. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual boiler inspection and maintenance check by a registered “Gas Safe” gas boiler service heating engineer is essential for safety and comply with UK Law.
The Engineer will make sure that the heating system is installed according to regulations during the annual central heating and boiler inspection, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler breakdowns and the resulting emergency repair work can often be avoided.
Condover Shropshire SY5 Super Low Energy Combi Boiler Inspection – A Number of Things You Will Want to Take Note Of
Combi boilers have a lot of advantages over conventional boilers, but also a few small drawbacks. This article will open your eyes to the things you should consider when purchasing a cheaper model. There are many models of combi boilers available in the market, and like in every other product, the price usually matches the quality and determines the results (you get what you pay for).
1) Possible scaling of the DHW heat exchanger
If the water company in your area, supplies you with hard water, chances are that your DHW heat exchanger will scale with time. In that scenario, you will have two choices; either replace it with an original piece from the manufacturer (which won't be cheap), or replace the whole boiler. Of course this problem can occur with any conventional tank as well, as this is one of the effects of hard waters. The latest and more expensive combi boilers are already designed to reduce scaling as much as possible. Another thing you could do is run softened water through it, but that would definitely invalidate your warranty.
2) No option of electric immersion heater
With a conventional water storage tank, if for some reason the boiler fails, you have the option of using an emergency electric immersion heater. But the combi boiler is tankless and this option would not be valid.
3)Possible incompatibility between gas pipes
You may need to upgrade the gas supply pipe, because the diameter may not comply with the regulations for installing combi boilers.
4)Good showers, slower baths
Although one of the combis' strengths is to be able to deliver high pressurized water in both your hot and cold taps, a cheaper model may have a modest flow rate of hot water. That is no problem if you are a shower person, because it will supply just what you need to take a nice hot shower. Nevertheless, it maybe a little slower for your bathtub to fill up.
5)It does not deliver instant hot water to all taps
If the boiler is far away from the tap you are using, it may take a few minutes for the hot water to come through, as it has to travel through many meters of cold water filled pipes. This is not a problem when filling up a tub or taking a shower, but if you just want instant hot water to wash your hands or fill up a basin, it may be irritating to have to wait and see an amount of cold water being wasted down the drain.
Why the Condensing Combi Boiler is a Very Popular Unit
Gas boilers normally extract the air they require for combustion either from inside the heated area or straight from the outside. Extracting air directly from outside, characteristically via a plastic pipe that moves through an outside wall, is more effective and secure.
This system is generally referred to as 'sealed combustion', since the gas is burned in a chamber that is blocked to engaged areas. This arrangement almost removes any hazard in the event of combustion gases seeping out into engaged areas.
The efficiency of gas boilers can be greatly increased by incorporating motorized dampers that block the flue pipe outlet when the boiler is not in use. This helps in preventing the loss of heated room air between boiler cycles. Another way to increase the efficiency of gas boilers is by using electric ignition. This does away with the necessity for a standing pilot light.
Gas boiler efficiency can also be enhanced by fan-assisted combustion systems, which do not call for a very big natural draft chimney and can be relieved through a minor flue pipe straight through a wall. Gas boilers, in reality, operate best at full load. When their intensity is lessened, they can drop by as much 20 percentage points in efficiency.
If building requirements are diverse, as is common in commercial buildings, multiple boilers are considered to be highly suitable. Generally, small gas boilers that function effectively are considered a better option than the most suitable of the bigger gas boilers. As has been observed, a number of small boilers can function more competently than a single big system. The reason is that each gas boiler can function frequently close to its full load, which is the most important yardstick for a gas boiler to function in an effective manner.
For Condover Shropshire SY5 Systems We Normally Advise Buying From The Worcester Combi Boiler Range
There comes a time in every homeowner's life when they must wrestle with the decision of whether or not they should repair their existing heating system, or bite the bullet and purchase a new one. Boilers and furnaces are one of the most expensive pieces of equipment in your home, so naturally you want to get as many years of service out of them as possible. Yet some times, it just doesn't make sense to make small repairs on a unit well past its prime.
The best way to prolong your system's lifespan is to ensure you have your system professionally serviced annually. This will help ensure the unit is running at maximum efficiency. It will also ensure that small problems are brought to light before they become larger expenses. However, when problems do come up, consider the following:
Is the problem easily fixable?There are many components of a HVAC unit that can easily be replaced; yet when some parts go it is much more difficult to fix. For example, ignition modules, thermocouples, or zone controls are all components that are easily replaced on heating systems. Yet, when a section of your boiler cracks, there is not much you can do except purchase a new unit.
Likewise, on air conditioners and heat pumps - many things can go wrong which are fixable. But when the evaporator coil or the condenser fails they are not easily repaired. And one of these parts needs to be replaced, it is best to replace the other with a compatible unit. Coils and condensers which are not matched can function together, but will not run optimally. Mismatched units will show decreases in performance, increased energy use, and premature system failure. So despite the higher initial cost, it is a smarter move to replace both components at the same time for maximum efficiency and prolonged equipment life.
Is the equipment inefficient?Another point of consideration is whether or not it pays to keep an outdated piece of equipment running in your home. If your boiler or furnace is over 15 years old, the efficiency is probably somewhere between 50-75%. Newer high efficiency models are between 85-95% efficient. Replacing an outdated unit with a new high efficiency model will save you money on your fuel bill.
What can go wrong next? If you have an older piece of equipment, you also must consider what may go wrong next. Making multiple small repairs can add up fast. If your unit is fixable, but the cost of repair is high, you may want to consider replacement. While it will be more expensive up front, you will save money in small repairs down the road, as well as save yourself a few headaches.