A gas boiler, fuelled with natural gas, oil, LPG or propane (etc), is the most common kind of appliance used for central heating in Cefn Einion Shropshire SY9 and throughout the United Kingdom. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual boiler inspection and maintenance check by a registered “Gas Safe” gas boiler service heating engineer is essential for safety and comply with UK Law.
The Engineer will make sure that the heating system is installed according to regulations during the annual central heating and boiler inspection, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler breakdowns and the resulting emergency repair work can often be avoided.
Cefn Einion Shropshire SY9 Super Low Energy Combi Boiler Inspection – A Number of Things You Need to Know
Worcester-Bosch is undoubtedly one of the leading manufacturers of gas-fired boilers in the UK, with a rich history spanning 50 years of production, Worcester is one the household names to look for when purchasing a new gas boiler for your home.
In August 2012, Worcester announced the launch (although to many say it was a revision) of the new Greenstar CDi Classic Combination Boiler Range.
A total of 8 models of boilers have been launched, they are:
Greenstar 29Cdi Classic – (Formerly Greenstar 27Cdi)
Greenstar 34Cdi Classic – (Formerly Greenstar 30Cdi)
Greenstar 38Cdi Classic- (Formerly Greenstar 37Cdi)
Greenstar 42Cdi Classic – (Formerly Greenstar 42Cdi)
All models are available in either standard natural gas, or in an LPG option for those in remote locations.
So What’s The Difference?
Most notably, the Greenstar Classic range has had a whole host of internal upgrades and improvements with the clever introduction of a more energy-efficient standby mode. With consumers continually looking at ways to reduce their energy consumption within the home, Worcester has managed to reduce the standby electricity output of the CDi boilers from 9W to just 3.5W in the new CDi Classic Boilers.
This enables customers to benefit from a more energy-efficient source of heating and hot water, which will have a positive impact on electricity bills. Therefore keeping a high standard in energy efficiency and maintaining the SEBUK A-Rated performance values in excess of 90% efficient.
The overall outputs of 27kW, 30kW and 37kW within the CDi range have been upgraded to 29kW, 34kW and 38kW in a move which substantially improves performance in flow rates, giving better hot water service to bathrooms and kitchens.
In addition to this increase in performance and reduction in energy consumption, the everyday operation has not been overlooked in this overhaul. The introduction of a magnetic flap access panel has greatly improved upon the Greenstar CDi’s original push and click mechanism, a feature which often failed with many years of use.
With peace of mind and reduced costs on everyone’s minds, Worcester hasn’t scrimped on the warranty either, with a current promotion of a full 5 Year parts and labour warranty on the boiler and a huge 10 Year Warranty on the primary heat exchanger.
Some features and benefits at a glance:
- Best boiler efficiency rating SEDBUK band A
- Fully condensing in both central heating and domestic hot water modes
- Keep hot facility – instantly available hot water
- Extremely small standby electrical output of 3.5W – energy efficient
- Wall mounting frame allows pipework to be hidden from view
- Vertical pre-piping kit
- Below boiler pipe cover
- Earth bonding strip
- Low NOx and CO2 emissions – environmentally friendly
- 5 year boiler guarantee until 31st December 2012, terms and conditions apply (standard guarantee: 2 years)
- 10 year guarantee on primary heat exchanger
- 5 year anti-scale guarantee on domestic hot water heat exchanger
- Hot water and central heating temperatures can be controlled
- Multi-directional fluing means boiler can be sited in a wider variety of places
- Mechanical, digital and new generation intelligent controls all compatible
- Heat load and flow generated precisely to meet the heating system’s requirements using a modulating pump
With the introduction of the new Greenstar Classic Combination boilers in 2012, Worcester’s continued program of improvements ensures they remain the UK’s favoured choice for boiler manufacturer, there is no better time to purchase a combi boiler to reduce bills and save energy.
Boilers, Furnaces and Central Air Conditioning – When To Fix, When To Replace
A gas boiler, fuelled with natural gas or propane, is one kind of appliance used for central heating. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual maintenance check by a registered gas boiler service heating engineer is very important for safety and efficiency. They will make sure that the heating system is installed according to regulations, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler repair work can be avoided.
In order for the boiler to be serviced properly, it needs to be working.
Gas boiler service varies according to the type of boiler, but there are some things that should be checked on in any boiler. This will be done by the engineer according to the instructions in the manual which came with the boiler when it was installed. The main things that should be checked are:
1. check for leaks
2. check the gas pressure
3. check if it is producing carbon monoxide
4. check if it is functioning properly
5. check the overall condition
6. check the pump and valves
7. check for enough ventilation
8. check the safety and cleanliness of the flue
Old cast iron boilers that have an open flue will need to be dismantled and cleaned which is not needed for modern boilers. They have a systems performance test. Depending on the condition and type of boiler it can take anywhere from half an hour to an hour and a half for a complete gas boiler service. Contractors are often willing to do servicing, especially during the summer, for greatly reduced prices, hoping that you will call them later if you need any gas boiler repair work.
If there is concern that a boiler is not working properly, and gas service is required, there are some things that can be checked:
1. Make sure there is enough water pressure by looking on the pressure gauge. It should show 1.0-1.5 bar.
2. Make sure the pilot light is lit.
3. If the pilot light is lit but there is no hot water, or it is unusually noisy, it may be a gas valve or pump failure in which case an engineer needs to be called.
4. If there is hot water but no central heating, the diverter valve may not be functioning.
5. If the top of the radiator is cold it may need to be “bled”. There is a bleed valve near the top that will release air. If it is cold on the bottom there is most likely sludge or rust blocking the radiator.
If there is no heat at all check the gas and make sure it is turned on as well as the thermostats and control switches. Make sure the pump is running and make sure the pilot light is lit. Many of these minor gas boiler repairs can be done at home with the use of the manufacturers’ manual. If you can identify a problem but are not sure how to fix it even with a manual, call a heating engineer for routine gas boiler service.
For Cefn Einion Shropshire SY9 Systems We Normally Suggest Purchasing From The Top Combi Boiler Range
By opting for a condensing boiler to convert the energy of natural gas to heat your home or apartment you are not only helping yourself by saving on heating bills but also make possible environmental well being while helping the whole world.
Wasted energy = wasted money
Whatever the fuel type may be, is said to be efficient about 90% at the lower end and – 98% at the upper. Your 15 year or so old traditional oil fired boiler is at least 12% less efficient than this. Whether it is gas or oil, you can imagine how much fossil fuel the high-efficiency boiler would conserve, how much CO2 emission it would curtail and the pile of moolah you would save during the next 30 or 40 year plus life span.
What makes a condensing boiler more efficient?
A traditional gas burning boiler or a condensing boiler of recent vintage technology is not different to any oil burning boiler in basic working mechanism. The extra bit of efficiency in the boiler is due to the condensation of water of combustion from steam state to liquid, releasing the latent heat of vaporisation. (Sadly if not for the condensing boiler, this huge percentage of heat energy will be sent up through the chimney as flue gases, without the homeowner having a clue to what’s happening). Inherently any boiler can achieve fuel efficiencies of 90% upwards easily.
A centralized heating system, incorporating a condenser boiler depends on several other system components. These would include the control system, DHW cylinders, Terminal units such as radiators etc. Unless there is a collectively efficient system in operation the ultimate overall efficiency will not be as desired.
Proprietary Brands and advanced designs
Proprietary brands such as Viessmann, a world leader in this field have developed technologies such as their stainless steel Inox-radial heat exchangers for natural gas combustion, capable of extracting almost to the end of last wave of thermal energy otherwise just wasted. Vitotronic controls (microprocessor-based control system), Vitocell domestic hot water cylinder, lambda pro control combustion controls (a metering system that adjusts the combustion process to the properties of any gaseous fuel) are other advanced features developed by them. The ultimate result is a very welcome consistent fuel efficiency of about 98%.