A gas boiler, fuelled with natural gas, oil, LPG or propane (etc), is the most common kind of appliance used for central heating in Copthorne and throughout the United Kingdom. It heats water which flows through pipes or a radiator, and it is used for hot water in the home as well as for a central heating system. It is also used for radiant floor heating systems. An annual boiler inspection and maintenance check by a registered “Gas Safe” gas boiler service heating engineer is essential for safety and comply with UK Law.
The Engineer will make sure that the heating system is installed according to regulations during the annual central heating and boiler inspection, that it is safe and it is working efficiently according to the manufacturers’ instructions. If this is done properly every year, gas boiler breakdowns and the resulting emergency repair work can often be avoided.
Copthorne High Energy Efficiency Combi Boiler Inspection – Several Things You Need to Take Note Of
Worcester-Bosch are undoubtedly one of the leading manufacturers of gas fired boilers in the UK, with a rich history spanning 50 years of production, Worcester are one the household names to look for when purchasing a new gas boiler for your home.
In August 2012, Worcester announced the launch (although to many say it was a revision) of the new Greenstar CDi Classic Combination Boiler Range.
A total of 8 models of boilers have been launched, they are:
Greenstar 29Cdi Classic - (Formerly Greenstar 27Cdi)
Greenstar 34Cdi Classic - (Formerly Greenstar 30Cdi)
Greenstar 38Cdi Classic- (Formerly Greenstar 37Cdi)
Greenstar 42Cdi Classic - (Formerly Greenstar 42Cdi)
All models are available in either standard natural gas, or in an LPG option for those in remote locations.
So What's The Difference?
Most notably, the Greenstar Classic range have had a whole host of internal upgrades and improvements with the clever introduction of a more energy efficient standby mode. With consumers continually looking at ways to reduce their energy consumption within the home, Worcester have managed to reduce the standby electricity output of the CDi boilers from 9W to just 3.5W in the new CDi Classic Boilers.
This enables customers to benefit from a more energy efficient source of heating and hot water, which will have a positive impact on electricity bills. Therefore keeping a high standard in energy efficiency and maintaining the SEBUK A-Rated performance values in excess of 90% efficient.
The overall outputs of 27kW, 30kW and 37kW within the CDi range have been upgraded to 29kW, 34kW and 38kW in a move which substantially improves performance in flow rates, giving better hot water service to bathrooms and kitchens.
In addition to this increase in performance and reduction in energy consumption, the everyday operation has not been overlooked in this overhaul. The introduction of a magnetic flap access panel has greatly improved upon the Greenstar CDi's original push and click mechanism, a feature which often failed with many years of use.
With peace of mind and reduced costs on everyone's minds, Worcester haven't scrimped on the warranty either, with a current promotion of a full 5 Year parts and labour warranty on the boiler and a huge 10 Year Warranty on the primary heat exchanger.
Some features and benefits at a glance:
- Best boiler efficiency rating SEDBUK band A
- Fully condensing in both central heating and domestic hot water modes
- Keep hot facility - instantly available hot water
- Extremely small standby electrical output of 3.5W - energy efficient
- Wall mounting frame allows pipework to be hidden from view
- Vertical pre-piping kit
- Below boiler pipe cover
- Earth bonding strip
- Low NOx and CO2 emissions - environmentally friendly
- 5 year boiler guarantee until 31st December 2012, terms and conditions apply (standard guarantee: 2 years)
- 10 year guarantee on primary heat exchanger
- 5 year anti-scale guarantee on domestic hot water heat exchanger
- Hot water and central heating temperatures can be controlled
- Multi-directional fluing means boiler can be sited in a wider variety of places
- Mechanical, digital and new generation intelligent controls all compatible
- Heat load and flow generated precisely to meet the heating system's requirements using a modulating pump
With the introduction of the new Greenstar Classic Combination boilers in 2012, Worcester's continued program of improvements ensures they remain the UK's favoured choice for boiler manufacturer, there is no better time to purchase a combi boiler to reduce bills and save energy.
Boiler Maintenance and Repair Tips
It is important to maintain boiler systems properly. The best way to do this is to get your boiler serviced frequently. Experts and manufacturers themselves recommend getting your boilers serviced at least once a year, to be on the safe side. Servicing a boiler can make it more efficient and increase its performance. This keeps it in a good and functional condition, making it last longer. Although the sound of servicing your boiler might seem expensive, especially on a yearly basis, the cost will only go up the longer you put it off. In addition to this, it can become harmful and dangerous to all those living in the same house.
A yearly servicing is the recommended frequency; however, there are a few exceptions to this rule that must be taken into account for. Moving into a new house with a boiler already installed needs to be serviced too before it is used. You cannot be sure how old the boiler is, or how long it has been since it was last used or serviced, so it is always best to be safe than sorry. Also, it is recommended to get your boiler serviced if you have been on an extended holiday where no-one has been at home to use the said boiler. A dormant boiler can be filled with anti-freeze that must be drained before use once again. Also, once again, after not being in use for a long time, you cannot be sure the condition of the boiler. There may be clogged or broken parts which to someone who isn't trained in the profession of servicing boilers would be unaware of.
The best time for getting a boiler service done is in between August and October, the last few months of summer. Not only is this after the holiday period, where you might have left the boiler unused for some amount of time, but these months are the in the off-peak season so many service providers would be both available and able to offer you a discount. This means that you can save on money and get a good, professional service from a trained and licensed expert without any hassle. Leaving the service for even a few weeks after this time period will see a rise in the price and the busyness of the workmen as winter comes around and boilers start to break and need fixing.
A good boiler service provider is someone who has a good reputation and is qualified. Finding someone like this isn't hard, as there are many professionals out there, however, it is essential that you make sure that the person you choose to hire is an expert in the boiler servicing field. Checking a person's or a company's licenses can be easily done by logging onto the Gas Safe Register in the United Kingdom and looking up their names. The industry of boiler servicing is very lucrative, with many of your local company's and independent workers offering competitive prices for a variety of different services including boiler servicing. It is important not to get too distracted by the pricing when hiring someone to do the job.
Your boiler system manual is the best place to start when looking for information about its servicing. The manufacturer can also help you by answering any questions you might have that are not mentioned in the manual. Phone numbers and email addresses are usually provided with the manual, but if not, it can be easily found on the internet.
For Copthorne Systems We Usually Advise Purchasing From The Our Recommended Combi Boiler Range
Combi boilers have a lot of advantages over conventional boilers, but also a few small drawbacks. This article will open your eyes to the things you should consider when purchasing a cheaper model. There are many models of combi boilers available in the market, and like in every other product, the price usually matches the quality and determines the results (you get what you pay for).
1) Possible scaling of the DHW heat exchanger
If the water company in your area, supplies you with hard water, chances are that your DHW heat exchanger will scale with time. In that scenario, you will have two choices; either replace it with an original piece from the manufacturer (which won't be cheap), or replace the whole boiler. Of course this problem can occur with any conventional tank as well, as this is one of the effects of hard waters. The latest and more expensive combi boilers are already designed to reduce scaling as much as possible. Another thing you could do is run softened water through it, but that would definitely invalidate your warranty.
2) No option of electric immersion heater
With a conventional water storage tank, if for some reason the boiler fails, you have the option of using an emergency electric immersion heater. But the combi boiler is tankless and this option would not be valid.
3)Possible incompatibility between gas pipes
You may need to upgrade the gas supply pipe, because the diameter may not comply with the regulations for installing combi boilers.
4)Good showers, slower baths
Although one of the combis' strengths is to be able to deliver high pressurized water in both your hot and cold taps, a cheaper model may have a modest flow rate of hot water. That is no problem if you are a shower person, because it will supply just what you need to take a nice hot shower. Nevertheless, it maybe a little slower for your bathtub to fill up.
5)It does not deliver instant hot water to all taps
If the boiler is far away from the tap you are using, it may take a few minutes for the hot water to come through, as it has to travel through many meters of cold water filled pipes. This is not a problem when filling up a tub or taking a shower, but if you just want instant hot water to wash your hands or fill up a basin, it may be irritating to have to wait and see an amount of cold water being wasted down the drain.